Diesel diagnostic software · Remote installationContact support
100% remote installation through TeamViewer or AnyDesk
Online service. Installed remotely on your computer.We connect through TeamViewer or AnyDesk. Your computer needs Internet access during installation; the agreed order defines the software and support included.

WORKSHOP MANUAL LIBRARY

barometric pressure DTCs Troubleshooting — RENR5088-10 — PDF,

This 13-page barometric pressure DTCs troubleshooting document provides the official Caterpillar diagnostic procedure for fault code 0108-04 (Barometric Pressure voltage low) on C15 On-Highway truck engines with MXS configuration. It details the conditions that generate the code, the ECM system response, and a multi-step electrical testing sequence to isolate the fault to the sensor, wiring harness, connectors, or ECM.

Official barometric pressure DTCs troubleshooting document details

Brand Caterpillar (CAT)
Model coverage C15 Truck Engine MXS (MXS00001-UP)
System / Group Engine Pressure Sensors / Diagnostic Trouble Codes
Publication no. RENR5088-10
Year / Revision Published 01/02/2009, Updated 25/02/2009
Pages 13
File size 0.3 MB
Format PDF
Language English

Document table of contents

  • 0108-04 Barometric Pressure voltage low (26) — Conditions Which Generate This Code, System Response
  • Engine Pressure Sensor Open or Short Circuit — Test (covers codes 100-3, 100-4, 102-3, 102-4, 108-3, 108-4, 385-3, 385-4)
  • Background Information — ECM pull-up voltage and diagnostic code activation
  • 108-3 Diagnostic Code and High Crankcase Pressure
  • Schematic for Engine Pressure Sensors (Illustration 1)
  • Locations of Engine Pressure Sensors — Boost, Barometric, Oil Pressure, Intake Valve Actuation (Illustrations 2–3)
  • Terminal Locations at the P2 ECM Connector (Illustration 4)
  • Terminal Locations at the Sensor Connector (Illustration 5)
  • Test Step 1 — Determine if the Code is Logged or Active
  • Test Step 2 — Check for Intermittent Connections at the Connectors
  • Test Step 3 — Check the Supply Voltage at the Sensor Connector (4.5–5.5 VDC)
  • Test Step 4 — Check for Battery Voltage on the Signal Wire
  • Test Step 5 — Check for an Open Circuit
  • Test Step 6 — Check the ECM for Proper Operation
  • Test Step 7 — Check the Signal Wire for a Short Circuit
  • Test Step 8 — Check ECM Detection of Open Circuit at P2 Connector

Applicable truck models

This procedure applies to C15 On-Highway Truck Engines with the MXS serial number prefix (MXS00001-UP). The document also references diagnostics relevant to the NKS and RKS configurations sharing the same pressure sensor circuits. It covers the atmospheric pressure sensor, boost pressure sensor, engine oil pressure sensor, and intake valve actuation system oil pressure sensor installed on these engines. Sensor terminal mapping at the P2 ECM connector includes pins P2-15, P2-17, P2-28, P2-54, P2-57, P2-72, P2-74, and P2-80. For additional technical resources, visit Caterpillar’s official support page.

Who needs this barometric pressure DTCs troubleshooting manual

Fleet mechanics and independent workshop technicians diagnosing a check engine lamp with DTC 0108-04 on CAT C15 engines will find this document essential. It is also valuable when troubleshooting the related -3 and -4 pressure sensor codes, since the procedure covers eight DTCs using a shared diagnostic workflow with multimeter tests, connector inspections, and ECM verification steps.

The full PDF is available in the DiagTechPro manuals library, free account required to download.

Related manuals library

barometric pressure DTCs Troubleshooting — RENR5088-10 — PDF, 1 / 3
barometric pressure DTCs Troubleshooting — RENR5088-10 — PDF, - preview page 1 of 3
barometric pressure DTCs Troubleshooting — RENR5088-10 — PDF, - preview page 2 of 3
barometric pressure DTCs Troubleshooting — RENR5088-10 — PDF, - page 3 is available after signing in
Free preview - 2 of 3 pages. Sign in to download the full PDF. Create a free account to download the full PDFNo credit card required · Instant download

Software for this brand

Diagnostic software for the same brand as this manual, installed remotely on your own laptop.

CAT SIS

CAT SIS

Original price was: 120 $.Current price is: 100 $. + 5% PayPal tax at checkout
WhatsAppWhatsApp us